www.sefindia.org

STRUCTURAL ENGINEERING FORUM OF INDIA [SEFI]

 Forum SubscriptionsSubscriptions DigestDigest Preferences   FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups  RegisterRegister FAQSecurity Tips FAQDonate
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log in to websiteLog in to websiteLog in to websiteLog in to forum 
Warning: Make sure you scan the downloaded attachment with updated antivirus tools  before opening them. They may contain viruses.
Use online scanners
here and here to upload downloaded attachment to check for safety.

As per IS 2502- 1963- Cutting length, Hook length, Bend length, Radius etc of a Stirrups

 
Post new topicReply to topic Thank Post    www.sefindia.org Forum Index -> SEFI General Discussion
View previous topic :: View next topic  
Author Message
sspawar
...
...


Joined: 05 Jun 2009
Posts: 1189

PostPosted: Sat Jan 22, 2022 7:27 am    Post subject: As per IS 2502- 1963- Cutting length, Hook length, Bend length, Radius etc of a Stirrups Reply with quote

Dear Sefians,
At many places in You Tubes and web sites, and forums, stirrups cutting length, bend and hooks  are explained in many ways following the thumb rules (of no basis) and many times with misconceptions which lead the questioners and seekers at no point and confused.
Some say for each 45 degree bend one D is deducted from overall length, some say it should be added, some say hook length will be 9d or 10d or 6d or anything.
Some say IS code gives insufficient information hence canít be followed exclusively.
I tried to explain on basis of IS code 2502 through a illustration which gives a complete picture how each and every length can be defined and calculated.
Regards



Warning: Make sure you scan the downloaded attachment with updated antivirus tools  before opening them. They may contain viruses.
Use online scanners
here and here to upload downloaded attachment to check for safety.
Bend Hook and Cutting length of Stirrups.pdf
 Description:

Download
 Filename:  Bend Hook and Cutting length of Stirrups.pdf
 Filesize:  153.8 KB
 Downloaded:  34 Time(s)



Last edited by sspawar on Mon Jan 24, 2022 9:07 am; edited 2 times in total
Back to top
View user's profile Send private message
vikram.jeet
General Sponsor
General Sponsor


Joined: 26 Jan 2003
Posts: 3250

PostPosted: Sat Jan 22, 2022 11:58 am    Post subject: Reply with quote

I think , we must differentiate between ANCHORAGE VALUE OF BEND /HOOK and LENGTH OF BAR consumed in bend (bend allowance / hook (hook allowance).

ANCHORAGE value of  bend is 8*bar dia for each 90 degree bend and for hook it is 16*bar dia. ( I.e. 4 *dia for every 45 deg bend)

Bend / Hook Allowance

Keeping in view the radius of bar ( cold twisted) being 4D and extra straight portion beyond bend / hook as also 4D

additional length consumed in 90 degree bend is around                    = 2π * (4D)/4 + 4D ~ 10D
Net bend allowance (since radius 4D is already taken in Bar straight Length ) = 6D

Similarly for hook  it works to around = 2π* (4D)/ 2 + 4D ~ 16 D
Net hook allowance = 12D
Above is based on inner radius of bend / hook  and π value taken approx as 3.0 . But it may be slightly higher taking centerline radius of bar and value of π as 3.142.
Back to top
View user's profile Send private message
sspawar
...
...


Joined: 05 Jun 2009
Posts: 1189

PostPosted: Mon Jan 24, 2022 6:44 am    Post subject: Reply with quote

Dear Sefians and Vikram Jeet Sir,
In the above topic I was only concerned of BBS preparation in light of IS 2502 for bend and hook of mainly of stirrups.
Whereas Design requirement  of reinforcement detailing regarding anchorage etc should be followed as per  IS 456 Clause 26.  

I further elaborated by sketch the stirrups of 135 degree hook detailing and last para of earlier pdf attachment is edited. Who have downloaded earlier PDF may go through the edited /updated PDF attachment in respect of 135 degree bend.

Regards



Warning: Make sure you scan the downloaded attachment with updated antivirus tools  before opening them. They may contain viruses.
Use online scanners
here and here to upload downloaded attachment to check for safety.
Bend Hook and Cutting length of Stirrups.pdf
 Description:

Download
 Filename:  Bend Hook and Cutting length of Stirrups.pdf
 Filesize:  153.8 KB
 Downloaded:  20 Time(s)

Back to top
View user's profile Send private message
vikram.jeet
General Sponsor
General Sponsor


Joined: 26 Jan 2003
Posts: 3250

PostPosted: Mon Jan 24, 2022 10:21 am    Post subject: Reply with quote

Dear Pawar saheb,

I appreciate you for bringing this delicate aspect into limelight as there always exist confusion and definitely your attachment is useful to all of us on sefi .

For BBS purpose / reinf quatty calculations   , the enlightenment of additional allowance  for  bars will end up in correct cutting of bars as also actual quatty consumption.

Please keep it up and best regards
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topicReply to topic Thank Post    www.sefindia.org Forum Index -> SEFI General Discussion All times are GMT
Page 1 of 1

 

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


© 2003, 2008 SEFINDIA, Indian Domain Registration
Publishing or acceptance of an advertisement is neither a guarantee nor endorsement of the advertiser's product or service. advertisement policy