www.sefindia.org

STRUCTURAL ENGINEERING FORUM OF INDIA [SEFI]

 Forum SubscriptionsSubscriptions DigestDigest Preferences   FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups  RegisterRegister FAQSecurity Tips FAQDonate
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log in to websiteLog in to websiteLog in to websiteLog in to forum 
Warning: Make sure you scan the downloaded attachment with updated antivirus tools  before opening them. They may contain viruses.
Use online scanners
here and here to upload downloaded attachment to check for safety.

Bend or Hook Allowance and Anchorage Value: Referring IS codes

 
Post new topicReply to topic Thank Post    www.sefindia.org Forum Index -> SEFI General Discussion
View previous topic :: View next topic  
Author Message
sspawar
...
...


Joined: 05 Jun 2009
Posts: 1204

PostPosted: Thu Jan 27, 2022 11:33 am    Post subject: Bend or Hook Allowance and Anchorage Value: Referring IS codes Reply with quote

Dear Sefians,
Earlier Vikram Jeet Sir has disguised the Allowances and Anchorage. By this topic I tried to define again referring IS codes.

Bend or Hook Allowance and Anchorage Value:

Bend or Hook Allowance length
As per IS2502, note 2 and figures 1A and 1B of clause 3.2.1 and tables II and others,it is sum of curved length and straight length beyond curve minus (kd+d)

Anchorage Value of a Bend or Hook
26.2.2 Anchoring Reinforcing Bars
26.2.2.1 Anchoring bars in tension
a) Deformed bars may be used without end anchorages provided development length requirement is satisfied. Hooks should normally he provided for plain bars in tension.
b) Bends and hooks - Bends and hooks shall conform to IS 2502
J) Bends-The anchorage value of bend shall be taken as 4 times the diameter of the bar for each 45t' bend subject to a maximum of 16 times the diameter of the bar.
2) Hooks-The anchorage value of a standard U-type hook shall be equal to 6 times the diameter of the bar.


As per IS456, of above clauses Anchorage Value of a Bend and Hook are very clear.

Clause 26.2.1 Development Length of Bars
NOTES
1 The development length includes the anchorage value of hooks in tension reinforcement.
2 For bars of sections other than circular development length should be sufficient to develop the stress in the bar by bond"

As per above notes it can be said that Anchorage value is an equivalent length to get margin to reduce total development length which create bond stresses, in case of tension reinforcement of plain bars only

If any addition alteration is there, please most welcome to elaborate further.
Regards



Warning: Make sure you scan the downloaded attachment with updated antivirus tools  before opening them. They may contain viruses.
Use online scanners
here and here to upload downloaded attachment to check for safety.
Allowance length of a Bend and Hook.pdf
 Description:

Download
 Filename:  Allowance length of a Bend and Hook.pdf
 Filesize:  26.4 KB
 Downloaded:  177 Time(s)

Back to top
View user's profile Send private message
Display posts from previous:   
Post new topicReply to topic Thank Post    www.sefindia.org Forum Index -> SEFI General Discussion All times are GMT
Page 1 of 1

 

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


© 2003, 2008 SEFINDIA, Indian Domain Registration
Publishing or acceptance of an advertisement is neither a guarantee nor endorsement of the advertiser's product or service. advertisement policy