www.sefindia.org

STRUCTURAL ENGINEERING FORUM OF INDIA [SEFI]

 Forum SubscriptionsSubscriptions DigestDigest Preferences   FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups  RegisterRegister FAQSecurity Tips FAQDonate
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log in to websiteLog in to websiteLog in to websiteLog in to forum 
Warning: Make sure you scan the downloaded attachment with updated antivirus tools  before opening them. They may contain viruses.
Use online scanners
here and here to upload downloaded attachment to check for safety.

Base Plate Design as per Chapter 12 of IS:800

 
Post new topicReply to topic Thank Post    www.sefindia.org Forum Index -> SEFI General Discussion
View previous topic :: View next topic  
Author Message
manish_nith
General Sponsor
General Sponsor


Joined: 24 Mar 2023
Posts: 3

PostPosted: Wed Apr 12, 2023 4:07 am    Post subject: Base Plate Design as per Chapter 12 of IS:800 Reply with quote

Hi Sefians,

I am trying to design a fixed base plate as per Chapter 12 of IS:800. As per my understanding following are the load cases I am considering while designing the base plate: (Column and Brace sections are considered Plastic sections)



(Please refer to attachment incase above pic is not visible in post)

Request your feedback on my understanding.

If someone can guide me to some solved example or some book that would be great help.

Regards
Manish Jain



Load_Cases.jpg
 Description:
Load Cases
 Filesize:  67.29 KB
 Viewed:  169 Time(s)

Load_Cases.jpg


Back to top
View user's profile Send private message
manish_nith
General Sponsor
General Sponsor


Joined: 24 Mar 2023
Posts: 3

PostPosted: Thu Apr 13, 2023 3:28 am    Post subject: Base Plate Design as per Chapter 12 of IS:800 Reply with quote

Hi Sefians,
I am trying to design a fixed base plate as per Chapter 12 of IS:800. As per my understanding following are the load cases I am considering while designing the base plate: (Column and Brace sections are considered Plastic sections)









(Please refer to attachment incase above pic is not visible in post)  Request your feedback on my understanding.  
If someone can guide me to some solved example or some book that would be great help.
Regards
Manish Jain  

Posted via Email



load_cases_836.jpg
 Description:
 Filesize:  67.29 KB
 Viewed:  169 Time(s)

load_cases_836.jpg


Back to top
View user's profile Send private message
arulsteel2
SEFI Member
SEFI Member


Joined: 19 Aug 2015
Posts: 2

PostPosted: Thu Apr 13, 2023 4:30 am    Post subject: Base Plate Design as per Chapter 12 of IS:800 Reply with quote

Dear Friends


Chapter 12 of IS: 800 is being revised and rationalized.  The EQ provisions in IS:800 is likely to be a separate part of IS:1893. When there was a wide circulation of that, very few responded.


Designers wish to exchange reliability for the economy. The clients often specify the cap on the steel tonnage and then ask the designers to design within that bracket. I faced the same issue in the design of a major project.  We must sensitize the clients that the reliability baseline cannot be lowered. 


Since such revisions come into vogue, we may have to extend the usage of IS:800 for EQ provisions.


On first look, the design combinations appear to be correct.


Warm regardsArul Jayachandran, Professor
IIT Madras






On Thu, Apr 13, 2023 at 9:02 AM manish_nith <forum@sefindia.org (forum@sefindia.org)> wrote:

Quote:
           Hi Sefians,
I am trying to design a fixed base plate as per Chapter 12 of IS:800. As per my understanding following are the load cases I am considering while designing the base plate: (Column and Brace sections are considered Plastic sections)









(Please refer to attachment incase above pic is not visible in post) Request your feedback on my understanding.
If someone can guide me to some solved example or some book that would be great help.
Regards
Manish Jain ]---c882a94f27bc9317d90cbf62fe55241d&m=139">
     



     
Download Attachments:
load_cases_836.jpg






Posted via Email
Back to top
View user's profile Send private message
sanjay puranik
SEFI Member
SEFI Member


Joined: 20 Jun 2016
Posts: 1

PostPosted: Thu Apr 13, 2023 11:30 am    Post subject: Base Plate Design as per Chapter 12 of IS:800 Reply with quote

The IS 800 chapter 12 is an atrocity From: "arulsteel2" <forum@sefindia.org>Sent: Thu, 13 Apr 2023 10:25:19To: general@sefindia.orgSubject: [SEFI] Base Plate Design as per Chapter 12 of IS:800Dear FriendsChapter 12 of IS: 800 is being revised and rationalized. The EQ provisions in IS:800 is likely to be a separate part of IS:1893. When there was a wide circulation of that, very few responded.Designers wish to exchange reliability for the economy. The clients often specify the cap on the steel tonnage and then ask the designers to design within that bracket. I faced the same issue in the design of a major project. We must sensitize the clients that the reliability baseline cannot be lowered. Since such revisions come into vogue, we may have to extend the usage of IS:800 for EQ provisions.On first look, the design combinations appear to be correct.Warm regardsArul Jayachandran, ProfessorIIT MadrasOn Thu, Apr 13, 2023 at 9:02â&euro;¯AM manish_nith <forum@sefindia.org (forum@sefindia.org)> wrote:                               --auto removed--

Posted via Email
Back to top
View user's profile Send private message
manish_nith
General Sponsor
General Sponsor


Joined: 24 Mar 2023
Posts: 3

PostPosted: Sat May 06, 2023 12:22 pm    Post subject: Re: Base Plate Design as per Chapter 12 of IS:800 Reply with quote

Thanks Professor Arul for your reply.

Following these cases, specially shear capacity clauses are very difficult in practical design.


Regards
Manish Jain
arulsteel2 wrote:
Dear Friends


Chapter 12 of IS: 800 is being revised and rationalized.  The EQ provisions in IS:800 is likely to be a separate part of IS:1893. When there was a wide circulation of that, very few responded.


Designers wish to exchange reliability for the economy. The clients often specify the cap on the steel tonnage and then ask the designers to design within that bracket. I faced the same issue in the design of a major project.  We must sensitize the clients that the reliability baseline cannot be lowered.


Since such revisions come into vogue, we may have to extend the usage of IS:800 for EQ provisions.


On first look, the design combinations appear to be correct.


Warm regardsArul Jayachandran, Professor
IIT Madras






On Thu, Apr 13, 2023 at 9:02 AM manish_nith <forum> wrote:

Quote:
            Hi Sefians,
I am trying to design a fixed base plate as per Chapter 12 of IS:800. As per my understanding following are the load cases I am considering while designing the base plate: (Column and Brace sections are considered Plastic sections)









(Please refer to attachment incase above pic is not visible in post) Request your feedback on my understanding.
If someone can guide me to some solved example or some book that would be great help.
Regards
Manish Jain
     



     
Download Attachments:
load_cases_836.jpg






Posted via Email

Back to top
View user's profile Send private message
Display posts from previous:   
Post new topicReply to topic Thank Post    www.sefindia.org Forum Index -> SEFI General Discussion All times are GMT
Page 1 of 1

 

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


© 2003, 2008 SEFINDIA, Indian Domain Registration
Publishing or acceptance of an advertisement is neither a guarantee nor endorsement of the advertiser's product or service. advertisement policy